Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
In this article down the page you will discover additional quality insight around Installing A Bathtub.
Setting up a tub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably tough task. If the old tub is readily accessible, the job can move immediately; if you have to open up a wall surface to remove the old bathtub and place the brand-new bath tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and embeded in the new one. Ensure you have certified yourself for the task and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly aid you mount a brand-new tub in your shower room if you have actually already acquired a new bathtub as well as don't need to transform the arrangement of your previous water supply pipelines.
Your devices and product list need to comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Safeguard the tap in position with the producer offered backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, position the bath tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost flexible tap port to the appropriate supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and examine all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill the tub as well as also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub must wait until the bath tub has been made use of a minimum of when as this will certainly resolve it into its final placement.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split an inflexible seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about issues with moisture and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can break fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub? Leave a remark directly below. We'd be interested to know your opinions about this entry. In hopes to see you back again later on. Sharing is nice. Who knows, you may very well be doing someone a favor. Thanks so much for taking the time to read it.
Guaranteed satisfaction offered. Report this page